ViewPower User’s Manual Management Software for Uninterruptible Power Supply Systems
9 Diagram 3-2 3.2. UPS Searching Step 1 C l i c k t h e U P S S e a r c h i n g ic on t o s earch UPS devices i n L A N o r I
10 Step 4 Cl ic k “ se arc h” b ut to n an d th e s ys t em w il l s t a rt s ear ch U PS s. All U PS s f ou nd in LAN or INTERNET will be l
1 1 3.3.2. UPS Remote Control & Monitor If you want to control and set up the remote UPS, you must log in as an administrator. There are two way
12 Method 2: Open IE and enter the remote UPS IP address and 15178. For example, remote UPS ID address is 202.16.53.142. Please enterhttp://202.
13 4. ViewPower Function Menu 4.1. ViewPower Configuration 4.1.1. Password Configuration I t ’ s password configuration for administrator only. Befo
14 4.1.2. SMS Configuration I t ’ s f o r entering SMS receiver list. In the event of an alarm condition occurring, a m e s s a g e a b o u t
15 Diagram 4-3 Diagram 4-4 4.1.3. E-mail Configuration This feature enables the configuration to send alarm m a i l b y S M T P s e r v e r .
16 Step 1 Select ViewPower Configuration >> E-mail. Refer to Diagram 4-5. Diagram 4-5 Step 2 Enter SMTP IP, user ID, and password. Click chec
17 3. Warning dialog (local): I t w i l l p o p u p a m e s s a g e d i a l o g a r o u n d t h e V i e w P o w e r oran ge p lug
18 4.1.5. Wake on LAN It will manage the list for wake on LAN and test the function. After adding MAC address of remote PCs into MAC list, it will a
1 Table of Contents 1. ViewPower Overview ... 2 1.1. Introduction ...
19 Diagram 4-8 Step 2 Select shutdown conditions and power-o f f o p t i o n s , s e t d e l a y t i m e t o s h u t d o w n system.
20 A c c e p t s h u t d o w n c o m m a n d f r o m r e m o t e s y s t e m : W h e n c l i c k i n g t h e c h e c k b o x ,
21 Diagram 4-9 Step 2 Select remote shutdown conditions. Step 3 Add/Delete remote system IP address. Step 4 Click “Apply” button to save all da
22 Step 1 Select UPS Setting >> Parameter Setting. Refer to Diagram 4-10. Diagram 4-10 Step 2 Select the functions by clicking “Enable” or “
23 Battery open status check: If enabled, the monitored UPS will check if the battery connection ok or not when UPS is turned on. Cold star
24 Diagram 4-11 Step 2 Enter data in the screen. Step 3 Click “Apply” button to save all data. 4.3. Control 4.3.1. Real-time Control Step 1 Sele
25 Step 2 Choose real-time control function by clicking “Start” button on each function section. Y o u c a n real-time control the UPS by executin
26 Step 2 Set frequency and setting time on the right column. NOTE: Rules for setting time. Daily schedule – P ow e r-off time should be earlier
27 Step 3 Click “Add” to add task. If task is successfully set, it will display on the task table on the left-hand side. Select specific task and cl
28 4.4.1.2. UPS Info Select View >> Status >> UPS Info. Refer to Diagram 4-16. Diagram 4-16 In the UPS Info window, it’s shown detaile
2 1. ViewPower Overview 1.1. Introduction ViewPower is UPS management software which is perfect for home users and enterprises. It can monit
29 Step 2 Select monitoring parameters on left-hand tab to switch diagram. Input voltage monitoring shows any change for input voltage. Output
30 Step 3 Select time period by clicking calendar icon. Then click “Browse” button to get list of all history events during selected period time. S
31 Diagram 4-20 Step 4 Click “Print” button to print event statistics. 4.4.2.3. Data I n t h e w i n d o w o f Data, i t s h o w s U
32 Step 2 Select UPS from com. port list. Users still can retrieve old data saved in the software even though the UPS is no longer connected to loca
33 4.5. Format Full Screen: C l i c k “ F u l l S c r e e n ” t o g e t t h e s o f t w a r e i n f u l l s c r e e n . T h e n
34 Appendix A: Glossary Local PC (system): The local PC (system) is physically connected to UPS with communication port. Remote PCs (systems)
3 Warning notifications via audible alarm, pop-up screen, broadcast, mobile messenger, and e-mail Scheduled UPS on/off, battery test, p
4 2.2. Software Install Step 1 Insert the ViewPower CD into CD ROM. ViewPower will display the installation menu, or you can run autorun.exe to start
5 Step 2 Click “Next” button to enter the pre-installation process. Refer to the following diagram 2-4. Diagram 2-4 Step 3 Click “Choose” button to
6 Step 4 Choose the shortcut folder and click “Next” button. Refer to the following diagram 2-6. Diagram 2-6 Step 5 I t w i l l d i s p l a y
7 Step 6 Click “Done” button to confirm the installation completely. Refer to Diagram 2-7. Diagram 2-8 2.3. Software Quick Start The Installer will
8 3. ViewPower GUI Interface The GUI has five sections as marked in the illustration below: Diagram 3-1 A. Function Menu offers complete tool-se
Comments to this Manuals